Automatic Wall-Mounted Electric Auto Foaming Soap Dispenser : Hand-Free, Rechargeable, touchless, Intelligent, Smart and Modern Hand soap Dispenser for bathrooms, Kitchens (White)

Price: $23.99
(as of Jun 16, 2025 01:10:12 UTC – Details)

Product Description

“Upgrade your space with the Novanex Soap Dispenser!

How to Use:

1: After receiving the product, please continue to charge it for 1-2 hours, and then use it after it is fully charged.

2: If you like to use foam hand soap, you can pour it directly without adding water.

3:If you like to use an ordinary thick gel hand soap, please add the hand soap first and then add water. The most appropriate ratio is 1 hand soap : 3 water, which can be adjusted according to the desired bubble concentration. Shake well. You can’t use a soap with particles, such as starlight hand soap, fluorescent hand soap etc, these particles can cause blockage.

4:If you like to use ordinary gel soap, please dilute it with a ratio of 1 soap: 2 water and shake well before adding it.

5:In order to avoid the blockage of the bubble outlet, caused by the viscous liquid , it is recommended to mix it in the container evenly and then pour it into the equipment.

6: IF you like to use thick gel hand soap, please dilute it with a ratio of 1 soap: 3 water and shake well before adding it.

7: Hang the device on the wall.

8:Press and hold the button on the right side till it says ON and then after its ON disappears it’s in standby mode.

Click the button twice and you’re ready for your liquid soap and it will dispense the right amount.

9: It takes one long press to turn it ON once you do that long press click the button on the side twice to set it according to your desired gear for your liquid soap and it will dispense the right amount and you’re all set.

10: Happy Dispensing and Enjoy the device

Installation Method

Clean the wall with a ragTear off the adhesive and paste it on the wall, let it stand for more than 24 hoursBuckle the machine on the adhesiveRead the user manualStart the machine

After receiving the product, please continue to charge it for 1.5-2 hours, and then use it after it is fully charged.

IF you face this issue :

You can feel it when you stretch your hand over, but no bubbles come out? Only a small amount of liquid comes out?

Answer : Probably due to the blockage of the outlet and the hand soap was not shaken evenly when adding the liquid, which caused the hand soap to precipitate, or the ordinary liquid hand soap was directly added to cause blockage. It is recommended to add warm water and adjust to the highest level for repeated induction.

In order to avoid the blockage of the bubble outlet, caused by the viscous liquid , it is recommended to mix it in the container evenly and then pour it into the equipment.

TROUBLESHOOTING GUIDES!

GUIDES FOR TROUBLESHOOTING!

Insufficient bubbles?

This is typically brought on by using too little regular liquid hand soap. We advise using a 1:3 ratio of regular liquid hand soap to water and recommending using more soap than less. Give it a good shake before using it.

We recommend that the ratio of ordinary hand soap to water is 1:3, and the amount of liquid soap should be more than less. Shake well before turning it on.

When you reach over, you can feel it, but no bubbles emerge? Just a tiny bit of liquid emerges?

Most likely as a result of the outlet obstruction, the hand soap precipitated because it was not shook evenly before adding the liquid, or it was put straight to the blockage by using regular hand soap. For repeated induction, it is advised to add warm water and adjust to the greatest level.

It happens Probably due to the blockage of the outlet, the hand soap was not shaken evenly when adding the liquid, which caused the hand soap to precipitate, or the ordinary liquid hand soap was directly added to can cause blockage. It is recommended to add warm water and adjust to the highest level for repeated induction.

The item you are currently seeing is a foam type. You can add foam soap straight into the mixture. If you decide to use regular gel soap, please dilute it beforehand by dilution 1 soap to 3 water ratio.

If you like to use ordinary gel hand soap or thick hand soap , please dilute it with a ratio of 1 soap: 3 water before adding it.

Not responding to the charge? The product is occasionally turned on while being transported, which results in the battery being totally depleted. Please continue charging the product for 1.5–2 hours after you receive it, and then use it once it is fully charged.

Does the soap dispenser froth on its own without a reach sensor? To avoid false induction brought on by reflections on the tabletop, we advise installing the machine more than 20 centimetres away from it.

Thick hand wash and non-foaming hand wash , shampoo and body wash need to be 1 : 3-5 times diluted with water and stirred well, so as not to cause machine failure

It is not recommended to use hand soaps containing particles, such as starry or fluorescent varieties, as these particles may clog pipes.

We also provide after-sales support. If your return window has closed, kindly notify us and we will take care of the issue. We appreciate your support.

Frequently Asked Questions

Commonly Asked Questions

Q: How do you add hand soap?

A: You can pour the foam hand soap straight without adding water.

A: If the soap is regular hand soap, please put the soap and water in that order. One hand soap to three water is the ideal ratio, which can be changed based on the desired bubble concentration.

Q: The soap dispenser is operational, but no bubbles are emitted.

A: The outlet is initially thought to be obstructed. Adding warm water and adjusting it to the maximum level for repeated dredging and induction is the solution.

If you like to use an ordinary hand soap, please add the hand soap first, and then add water. The most appropriate ratio is 1 hand soap : 3 water, which can be adjusted according to the desired bubble concentration.

Can’t use a soap with particles, such as starlight hand soap, fluorescent hand soap, etc., particles can cause blockage

NOTE :Black sponge cannot sense (because black sponge absorbs infrared rays, black sponge cannot be used for sensing)

Specification: 5.1in/13cm x 2.5 in/6.2cm

Maximum capacity: 300ml/12ozBattery capacity: 2000 mAhProduct weight: 380g/0.83lbWaterproof level: IPX5Installation method: strong non-marking glue wall-mounted

Standard Technical Specifications

Specification: 5.1in/13cm x 2.5 in/6.2cm Maximum capacity: 300ml/12oz Battery capacity: 2000 mAh Product weight: 380g/0.83 lb

More Details

IMPORTANT POINTS:

HOW TO PROLONG ITS SERVICE LIFE? WHY IT IS STOP WORKING AFTER SEVERAL MONTHS ?

Cause of problem : Internal pipe blockage, due to long time of no use or frequent use of high-viscose soap without mixing it with the water.

Foam doesnot adhere to the apparatus

45° bionic inclination angle, foam does not stick to the machine

Fast Bubbles

Incredibly quick foaming in 0.25 seconds ; no waiting

Wall-Mounted Automatic Soap Dispenser

Press and hold the button on the right side till it says ON and then after its ON disappears it’s in standby mode.

Click the button twice and you’re ready for your liquid soap and it will dispense the right amount.

Installation Method

Clean the wall with a ragTear off the adhesive and paste it on the wall, let it stand for more than 24 hoursBuckle the machine on the adhesiveRead the user manualTurn on the device

It takes one long press to turn it ON , once you do that long press click the button on the side twice to set it for your liquid soap, it will dispense the right amount and you’re all set.

Every product is lovingly constructed

Waterproof level: IPX5Installation method: strong non-marking glue wall-mounted

{ADAPTABLE THREE-LEVEL SYSTEM } You’ve come to the right place if you’re searching for an automated soap dispenser that prioritises customisation! You may customise our dispenser to meet your needs thanks to its three distinct bubble settings. A superior infrared sensor is also included, capable of detecting even the strongest light; just be sure to position it at the proper distance.Place it 20 cm/0.65 feet away from your table.
{A COMPLETE SCREEN DISPLAY } Prepare to be amazed by the full-screen display on this soap dispenser! It displays the inside temperature as well as the remaining power. Furthermore, you can use it in humid conditions without worrying about damage because it is waterproof (IPX5). Ensure that the sensor remains dry! On cement walls, do not use traceless stickers.)
{FIT FOR A VARIETY OF SOAPS }This dispenser can take any type of soap you like, whether it’s body wash, dish soap, or hand soap. Additionally, you may get up to 300 uses out of its sizable 12 oz/300 ml capacity, which could serve your family for about 50 days.(Foam soap can be added straight; regular gel soap must be diluted with water.)
Enjoy upto 3 months’ worth of battery life Put an end to having to recharge your soap dispenser all the time! You may use it without needing to recharge for up to four whole months because to our built-in 2000 capacity battery. You can enjoy it for longer because it uses less energy and runs softly thanks to worldwide advanced motor technology.
* INSTALLATION WITHOUT A DRILL* Our recharging soap dispenser is simple to mount on smooth surfaces like tile or mirrors and comes with strong adhesive strips that won’t leave any marks. In addition, you receive a one-year warranty and round-the-clock assistance for any problems. Purchase with assurance, and if you run into any issues, simply send us an email on Amazon, and we’ll respond right away! Email:[email protected]
After receiving the product, please continue to charge it for 1-2 hours, and then use it after it is fully charged. IF you like to use ordinary gel soap, please dilute it with a ratio of 1 soap: 2 water and shake well before adding it. IF you like to use thick gel hand soap, please dilute it with a ratio of 1 soap: 3 water and shake well before adding it. The most appropriate ratio is 1 hand soap : 3 water, which can be adjusted according to the desired bubble concentration. Shake well. Hang the device on the wall while using Traceless stickers.
Press and hold the button on the right side till it says ON and then after its on disappears it’s in standby mode. Click the button on the side twice to set it according to your desired gear for your liquid soap and it will dispense the right amount and you’re all set. Happy Dispensing and Enjoy the device